The employment of water vapor and other gases plasma for biomass and solid fuel conversion, neutralization of hazardous materials and etc.
Equipment is designed for measuring concentration of solid particles in air/gas and also for determination of combustion gas composition.
Thermal analysis of materials with evolved gas analysis by FTIR and GCMS methods.
Determination of heating value of biofuel, mixtures and calorific waste for determination of suitability of combustion in industrial furnaces.
Applicable for combustion process diagnostics, analysis of other fast processes where optical sensitivity is necessary.
Applicable for the spectral analysis of liquid, solid and gaseous samples of organic or non-organic origin, and dynamic mode of spectral analysis of evolved gases.
Used for the analysis of the products from biofuel thermal destruction (gasification) and combustion.
Solid fuel and high-calorie waste sample preparation for supply them to the analytical instruments and making suitable working conditions for samples mineralization.
The system is intended to use in studies of biofuel combustion efficiency.
Determination Cl, F, Br concentration in the fuel to assess the potential environmental impact of harmful elements and fuel quality indicators.
For various biomass pellets combustion parameters and emissions studies.
Studies of gasification process of solid recovered fuels, i.e., separation of synthesized gas phase in the reactor and subsequent determination of the gas parameters and its application.
To visualize ash melting state and analyze conditions to get information about ash softening, melting processes, depending on the temperature or its gradient values changes.
The influence of the humidity of air supplied for combustion on combustion process efficiency.
Studies on measurement accuracy of air humidity sensors.
Studies on fluid and gas dynamics at low speeds near the surface of the membrane and various trace elements, surface fouling.
The calorific analysis of natural, pyrolysis, liquefied petroleum gas, biogas and gas mixtures.
Heat flow visualization and measurement.
Combustion analysis of heating equipment (boilers, fireplaces, etc.) fired with solid and liquid fuel at operation site.
Determination and analysis of ash content, volatile matter and volatile composition of biofuels and recovered fuels Analysis of materials state transitions.
Major and minor element analysis of liquid and solid organic and mineral compounds of biofuels and recovered fuel.
Solid and liquid fuels, including biofuels and recovered fuel samples weighing in fuel moisture and ash analysis.
Analysis of the main chemical elements C / H / N / S and O in solid and liquid fuels, including biofuels and recovered fuels.
Research and testing of thermal equipment (boilers, fireplaces, etc.) with solid biomass and recovered fuel, and with liquid and gaseous fuels.
Studies of the particles dynamics in liquid and gas flows and flows interaction with surfaces and flow round bodies in order to increase efficiency of combustion processes and water treatment in plants and as well as to model momentum and heat transfer processes.
Very small air (gas) flow measurement in small-diameter channels or streams flowing through membranes;
Air-gas (sample) volume measurements at various gas formation and quantitative characteristics of analysers.
Evaluation of fuel quality, prices, quantities of heat and, performance parameters of thermal equipment.
Height 50 m, aluminium lattice structure, mounted on steal plate, guyed with wires with attached measurement equipment.
Measurements of wind speed, direction, atmospheric pressure, temperature and humidity.
Bruel&Kjaer high quality noise level analyzer with sound level calibrator.
The preparation of solid and calorific waste and soft, hard, elastic and fibrous materials of 0,25 ÷ 20 mm fractions. Compression of crushed materials into suitable samples for analysis. Ensuring proper working conditions while mineralizing the samples. Preparation of deionised water for mineralization of samples.
Measurements of temperature, pressure, differential pressure and speed, measurement data collection and recording.
The determination of the Cl, F, Br concentration in the fuel in order to assess possible environmental pollution with harmful elements and evaluation of fuel quality indicators.
Research of furnaces up to 25 kW fired with biofuel pellets.
Scientific research on solid fuel gasification in order to find wider applications or to improve quality.
It is intended to analyze the ash melting state and conditions and to visualize how the softening and melting processes of ash take place, depending on the temperature or variation of its gradient value.
Investigations of low velocity liquid and gas dynamics at surfaces, membranes and various microelements, surface contamination, motion and mass transfer processes in capillary systems.
Identification and analysis of upper and lower heating values of gaseous fuels, including biofuels and recovered fuels. Determination and analysis of upper and lower heating values of other calorific materials (eg sewage sludge, waste, etc.).
Measurement and visualization of heat flux from surfaces for determination of heat loss, its location, insulation efficiency.
Determination of composition of combustion products (CO, CO2, NO, NOx, CiHy, O2, SO2) for the evaluation of the efficiency of thermal equipment, fuel combustion rate, emissions to environment under research and operational conditions; optimization of device operating regimes.
Identification of fuel quality indicators performing research and development.
Determination of fuel elements in order to assess the fuel quality indicators and possible environmental pollution with harmful elements.
Precise measurements of fuel humidity and ash content, assessment of fuel quality indicators and combustion rate.
The determination of the chemical elements C/H/N/S and O in the fuel, evaluation of its qualitative and quantitative indicators.
The determination of composition (CO, CO2, NO, NOx, CiHy, O2, SO2) of combustion products for the evaluation of the efficiency of thermal equipment, fuel combustion and emissions to the environment.
The determination of the upper and lower calorific values and analysis of solid and liquid fuels, including biofuels and recovered fuels.
The measurement of wind speed and direction, maintenance of equipment, data analysis.
The calculation of wind energy resources, the planning of wind power park layout, the economic calculations.
Simulation and visualization of blades shadow zones around wind power plant.
Modeling and visualization of noise dispersion zones around noise sources.
Measurement of noise level in industrial and residential environments.
Software for calculation and visualisation of wind power resources.
Modeling of wind power resources, wind farm planning, modeling of wind turbine noise and flicker.
Management and analysis of digital maps and other visual data. Creation, management and analysis of visual data, illustration of reports.
The preparation of solid and calorific waste and soft, hard, elastic and fibrous materials of 0,25 ÷ 20 mm fractions. Compression of crushed materials into suitable samples for analysis. Ensuring proper working conditions while mineralizing the samples. Preparation of deionised water for mineralization of samples.
Measurements of temperature, pressure, differential pressure and speed, measurement data collection and recording.
The determination of the Cl, F, Br concentration in the fuel in order to assess possible environmental pollution with harmful elements and evaluation of fuel quality indicators.
Research of furnaces up to 25 kW fired with biofuel pellets.
Scientific research on solid fuel gasification in order to find wider applications or to improve quality.
It is intended to analyze the ash melting state and conditions and to visualize how the softening and melting processes of ash take place, depending on the temperature or variation of its gradient value.
Investigations of low velocity liquid and gas dynamics at surfaces, membranes and various microelements, surface contamination, motion and mass transfer processes in capillary systems.
Identification and analysis of upper and lower heating values of gaseous fuels, including biofuels and recovered fuels. Determination and analysis of upper and lower heating values of other calorific materials (eg sewage sludge, waste, etc.).
Measurement and visualization of heat flux from surfaces for determination of heat loss, its location, insulation efficiency.
Determination of composition of combustion products (CO, CO2, NO, NOx, CiHy, O2, SO2) for the evaluation of the efficiency of thermal equipment, fuel combustion rate, emissions to environment under research and operational conditions; optimization of device operating regimes.
Identification of fuel quality indicators performing research and development.
Determination of fuel elements in order to assess the fuel quality indicators and possible environmental pollution with harmful elements.
Precise measurements of fuel humidity and ash content, assessment of fuel quality indicators and combustion rate.
The determination of the chemical elements C/H/N/S and O in the fuel, evaluation of its qualitative and quantitative indicators.
The determination of composition (CO, CO2, NO, NOx, CiHy, O2, SO2) of combustion products for the evaluation of the efficiency of thermal equipment, fuel combustion and emissions to the environment.
The determination of the upper and lower calorific values and analysis of solid and liquid fuels, including biofuels and recovered fuels.
The measurement of wind speed and direction, maintenance of equipment, data analysis.
The calculation of wind energy resources, the planning of wind power park layout, the economic calculations.
Simulation and visualization of blades shadow zones around wind power plant.
Modeling and visualization of noise dispersion zones around noise sources.
The employment of water vapor and other gases plasma for biomass and solid fuel conversion, neutralization of hazardous materials and etc.
Equipment is designed for measuring concentration of solid particles in air/gas and also for determination of combustion gas composition.
Thermal analysis of materials with evolved gas analysis by FTIR and GCMS methods.
Determination of heating value of biofuel, mixtures and calorific waste for determination of suitability of combustion in industrial furnaces.
Applicable for combustion process diagnostics, analysis of other fast processes where optical sensitivity is necessary.
Applicable for the spectral analysis of liquid, solid and gaseous samples of organic or non-organic origin, and dynamic mode of spectral analysis of evolved gases.
Used for the analysis of the products from biofuel thermal destruction (gasification) and combustion.
Solid fuel and high-calorie waste sample preparation for supply them to the analytical instruments and making suitable working conditions for samples mineralization.
The system is intended to use in studies of biofuel combustion efficiency.
Determination Cl, F, Br concentration in the fuel to assess the potential environmental impact of harmful elements and fuel quality indicators.
For various biomass pellets combustion parameters and emissions studies.
Studies of gasification process of solid recovered fuels, i.e., separation of synthesized gas phase in the reactor and subsequent determination of the gas parameters and its application.
To visualize ash melting state and analyze conditions to get information about ash softening, melting processes, depending on the temperature or its gradient values changes.
The influence of the humidity of air supplied for combustion on combustion process efficiency.
Studies on measurement accuracy of air humidity sensors.
Studies on fluid and gas dynamics at low speeds near the surface of the membrane and various trace elements, surface fouling.
Manufacturer: Dantec Dynamics
The calorific analysis of natural, pyrolysis, liquefied petroleum gas, biogas and gas mixtures.
Combustion analysis of heating equipment (boilers, fireplaces, etc.) fired with solid and liquid fuel at operation site.
Determination and analysis of ash content, volatile matter and volatile composition of biofuels and recovered fuels Analysis of materials state transitions.
Major and minor element analysis of liquid and solid organic and mineral compounds of biofuels and recovered fuel.
Solid and liquid fuels, including biofuels and recovered fuel samples weighing in fuel moisture and ash analysis.
Analysis of the main chemical elements C / H / N / S and O in solid and liquid fuels, including biofuels and recovered fuels.
Research and testing of thermal equipment (boilers, fireplaces, etc.) with solid biomass and recovered fuel, and with liquid and gaseous fuels.
Studies of the particles dynamics in liquid and gas flows and flows interaction with surfaces and flow round bodies in order to increase efficiency of combustion processes and water treatment in plants and as well as to model momentum and heat transfer processes.
Manufacturer: Dantec Dynamics
Very small air (gas) flow measurement in small-diameter channels or streams flowing through membranes;
Air-gas (sample) volume measurements at various gas formation and quantitative characteristics of analysers.
Manufacturer: Sierra Instruments
Evaluation of fuel quality, prices, quantities of heat and, performance parameters of thermal equipment.
Software for calculation and visualisation of wind power resources.
Modeling of wind power resources, wind farm planning, modeling of wind turbine noise and flicker.
Management and analysis of digital maps and other visual data. Creation, management and analysis of visual data, illustration of reports.
Height 50 m, aluminium lattice structure, mounted on steal plate, guyed with wires with attached measurement equipment.
Measurements of wind speed, direction, atmospheric pressure, temperature and humidity.
Manufacturer: LSI Lastem
Bruel&Kjaer high quality noise level analyzer with sound level calibrator.
